濃相氣力輸灰系統采用了先進成熟的管道二相流技術，實現粉料顆粒的高效、可靠、低能耗、長距離輸送;是燃煤電鍋爐飛灰處理的理想設備[系統]。

　　The dense phase pneumatic ash conveying system adopts advanced and mature pipeline two-phase flow technology to achieve efficient, reliable, low-energy consumption, and long-distance transportation of powder particles; It is an ideal equipment [system] for fly ash treatment of coal-fired power boilers.

　　二、系統工藝流程

　　2、 System Process Flow

　　本系統由倉泵、氣源、管道和灰?guī)斓炔糠纸M成，采用集中程序控制方式，實現系統設備的協調有序運行。

　　This system consists of warehouse pumps, gas sources, pipelines, and ash storage, and adopts centralized program control to achieve coordinated and orderly operation of system equipment.

　　系統采用F型上引式流態化倉泵作為關鍵輸送設備，倉泵直接連接在電除塵器灰斗下，接受電除塵器收集的飛灰，同時采用空氣壓縮機作為動力源，通過密閉的管道，在高濃度、低流速的狀態下，把飛灰輸送至貯灰?guī)臁?/p>

　　The system adopts an F-type upward fluidized bed bin pump as the key conveying equipment. The bin pump is directly connected to the ash hopper of the electrostatic precipitator, receiving the fly ash collected by the electrostatic precipitator. At the same time, an air compressor is used as the power source to transport the fly ash to the ash storage silo through a closed pipeline under high concentration and low flow rate conditions.

　　三、濃相氣力輸灰系統典型設備配置1.流態化倉泵   F型上引式流態化倉泵為一耐疲勞,耐磨損的低壓容器，倉泵本體上封頭內集成有氣動進料閥，以控制飛灰進入倉泵，下封頭設一流化氣室，內裝流化盤，流化氣室與進氣管道相聯，并通過氣動進氣閥控制壓縮空氣的流入，出料管從流化盤中心附近向上引出泵體并與氣動出料閥相聯，出料閥控制灰氣混合物排入管道;為滿足自動控制的要求，倉泵體上還裝有料位計和壓力傳感器。

　　3、 Typical equipment configuration for dense phase pneumatic ash conveying system: 1. Fluidized bed bin pump F-type upward fluidized bed bin pump is a low-pressure vessel that is fatigue resistant and wear-resistant. The upper head of the bin pump body is integrated with a pneumatic feed valve to control the entry of fly ash into the bin pump. The lower head is equipped with a fluidized bed chamber, which is connected to the inlet pipeline and controls the inflow of compressed air through the pneumatic inlet valve. The discharge pipe leads out the pump body from near the center of the fluidized bed and is connected to the pneumatic discharge valve. The discharge valve controls the discharge of the ash gas mixture into the pipeline; To meet the requirements of automatic control, the bin pump body is also equipped with a level gauge and pressure sensor.

　　2.氣源系統

　　2. Gas source system

　　氣源由空氣壓縮機壓縮空氣凈化過濾設備及貯氣罐等組成?？諌簷C一般采用流量10~20m3/min壓力0.8MPa的螺桿式空壓機，對于連續運行工況，螺桿式空壓機比活塞往復式空壓機具有更高的可靠性，貯氣罐起到穩定壓力、緩沖用氣、冷卻除水等作用，為滿足間歇用氣的工況要求，一般選用較大容量的貯氣罐，由于空壓機排出的壓縮空氣中含有大量的水份，包括液態水份和氣態水份，這些水份對飛灰輸送是不利的，可采用多級過濾除去液態水份，同時采用干燥機[冷凍干燥機或吸附式干燥機]除去部分氣態水份，降低壓縮空氣露點，以防止和飛灰混和時產生結露、結塊等現象。3.輸送管道

　　The air source consists of compressed air from an air compressor, air purification and filtration equipment, and gas storage tanks. Generally, screw air compressors with a flow rate of 10-20m3/min and a pressure of 0.8MPa are used for air compressors. For continuous operation, screw air compressors have higher reliability than piston reciprocating air compressors. The air storage tank plays a role in stabilizing pressure, buffering gas, cooling and removing water. In order to meet the requirements of intermittent gas use, larger capacity air storage tanks are generally selected. Due to the large amount of moisture, including liquid and gaseous moisture, in the compressed air discharged by the air compressor, which is not conducive to fly ash transportation, multi-stage filtration can be used to remove liquid moisture. At the same time, a dryer [freeze dryer or adsorption dryer] can be used to remove some gaseous moisture, reduce the dew point of compressed air, and prevent condensation, agglomeration and other phenomena when mixed with fly ash. 3. Transportation pipeline

　　由于系統輸送流速較低，輸灰管道可采用普通無縫鋼管，壁厚一般6 ~ 8mm。根據出力要求及輸送距離，采用管徑般有以下幾種規格: DN65. DN80. DN100和DN125. 遠距離輸送時，為降低末端輸送流速，可采用輸送管道變徑方式，輸送管道彎頭也可采用耐磨管或無縫鋼管背部加厚。

　　Due to the low conveying flow rate of the system, ordinary seamless steel pipes with a wall thickness of generally 6~8mm can be used for the ash conveying pipeline. According to the output requirements and conveying distance, there are generally several specifications of pipe diameters used: DN65, DN80, DN100 and DN125. When conveying at a long distance, to reduce the end conveying flow rate, the conveying pipeline diameter can be changed, and the conveying pipeline elbow can also use wear-resistant pipes or seamless steel pipe back thickening.

　　4.自動控制系統

　　4. Automatic control system

　　本系統整個工藝流程采用計算機集中程序控制，全自動運行。運行人員只需監視控制系統運行顯示狀態。同時由于設有完善的故障報警系統，故障處理和維護都十分方便。

　　The entire process of this system is controlled by a computer centralized program and runs fully automatically. Operators only need to monitor the display status of the control system operation. At the same time, due to the comprehensive fault alarm system, fault handling and maintenance are very convenient.

　　四、系統控制過程特點如下

　　4、 The characteristics of the system control process are as follows

　　程序控制器根據輸入信號，通過程序運行輸出來控制整個系統工藝流程。一臺程序控制器可同時控制多臺倉泵協調運行。系統還設有現場控制箱，可進行現場手動操作，以滿足調試和現場故障處理要求。

　　The program controller controls the entire system process flow through program execution output based on input signals. A program controller can simultaneously control the coordinated operation of multiple bin pumps. The system also has an on-site control box that can be manually operated on site to meet the requirements of debugging and on-site fault handling.

　　程序控制器在控制工藝流程的同時，動態顯示各運行參數狀態，給出設備故障報警信自動進行部分故障緊急處理。

　　The program controller dynamically displays the status of various operating parameters while controlling the process flow, and provides equipment fault alarm signals for automatic emergency handling of partial faults.

　　系統運行參數在控制器上可動態自由設定和調整，因此具有極大的靈活性和適應性。

　　The system operating parameters can be dynamically and freely set and adjusted on the controller, thus having great flexibility and adaptability.

　　系統運行參數在控制器上可動態自由設定和調整，因此具有極大的靈活性和適應性。

　　The system operating parameters can be dynamically and freely set and adjusted on the controller, thus having great flexibility and adaptability.

　　本文由 氣力輸送系統  友情奉獻.更多有關的知識請點擊  http://m.kingwanlan.com/   真誠的態度.為您提供為全面的服務.更多有關的知識我們將會陸續向大家奉獻.敬請期待.

　　This article is a friendly contribution from the pneumatic conveying system For more related knowledge, please click http://m.kingwanlan.com/ Sincere attitude To provide you with comprehensive services We will gradually contribute more relevant knowledge to everyone Coming soon.