氣力輸送旋轉供料器該如何維修?盡管旋轉供料器看起來很簡單，但它們對于基于氣力輸送系統的粉末輸送控制至關重要。旋轉供料器務必處在優質情況，才能確保系統安全平穩地運作。如果您的旋轉供料器有問題，那么降低系統的速度進行維護是很重要的，這將需要大量的時間和費用。然而，通過適度、及時地旋轉供料器，可以防止這種昂貴的維護和停機時間。這不但能夠使輸送操作更暢順，并且能夠提升旋轉供料器特性。下面小編將分享六個易于遵循的維護程序，以幫助您維護旋轉供料器，避免浪費昂貴的停機時間。

　　How to repair the pneumatic conveying rotary feeder? Although rotary feeders may seem simple, they are crucial for powder conveying control based on pneumatic conveying systems. The rotary feeder must be in high-quality condition to ensure the safe and smooth operation of the system. If there is a problem with your rotary feeder, it is important to slow down the system for maintenance, which will require a significant amount of time and cost. However, by rotating the feeder moderately and promptly, this expensive maintenance and downtime can be prevented. This not only makes the conveying operation smoother, but also enhances the characteristics of the rotary feeder. Below, the editor will share six easy to follow maintenance procedures to help you maintain the rotary feeder and avoid wasting expensive downtime.

　　01查驗旋轉供料器閘閥內部伴隨著散粉末狀持續穿過您的旋轉供料器，定期維護閘閥內部十分關鍵。這包括檢查電機轉子、電機轉子葉片、液壓密封件、外殼和端板的狀況。您可以根據維護門（如果配備一個閘閥）或根據閘閥的拆卸和組裝的一部分輕松檢查閘閥。如果檢測到任何損壞，應在再次為旋轉供料器的運行提供資金之前進行維護。

　　01 Check the rotary feeder gate valve for continuous passage of loose powder particles through your rotary feeder. Regular maintenance of the gate valve is crucial. This includes checking the condition of the motor rotor, motor rotor blades, hydraulic seals, housing, and end plates. You can easily inspect the gate valve based on maintenance (if equipped with a gate valve) or as part of the disassembly and assembly of the gate valve. If any damage is detected, maintenance should be carried out before providing funding for the operation of the rotary feeder again.

　　02檢查水泵密封件和滾動軸承。檢查電機轉子軸支撐點的側隙是否過大，滾動軸承是否平穩運行。在嚴重?fù)p壞之前及時將其拆下并更換，因為損壞的滾動軸承可能會損壞外殼中的電機轉子部分，并由于金屬材料與不可分割間隙中的金屬材料之間的接觸而造成損壞。還應最少每個月查驗一次水泵密封。在包裝種類液壓密封件上，扭緊旋蓋固定夾板并在液壓密封件剛開始泄露以前拆換液壓密封件。對于氣體吹掃密封而言，保持水泵在氣體吹掃旋轉閥上的適度密封至關重要。

　　02 Check the water pump seals and rolling bearings. Check if the side clearance of the motor rotor shaft support point is too large and if the rolling bearings are running smoothly. Remove and replace it in a timely manner before serious damage occurs, as damaged rolling bearings may damage the motor rotor part in the housing and cause damage due to contact between the metal material and the metal material in the inseparable gap. The water pump seal should also be inspected at least once a month. On the packaging type hydraulic seal, tighten the cap fixing clamp and replace the hydraulic seal before it starts to leak. For gas blowing sealing, it is crucial to maintain a moderate seal of the water pump on the gas blowing rotary valve.

　　03查驗旋轉供料器轉嫩葉尖空隙是不是密不可分，因為旋轉供料器和閘閥必須控制十分細的粉末狀穿過有時候高壓差，因而轉嫩葉尖空隙必須十分密不可分。不然，您的輸送系統的特性將遭遇風險性。為了防止氣鎖蒸汽泄漏過多而造成潛在問題，請按照以下所示的保證間隙擰緊：鎖定旋轉給料機電機的開關電源。如果可以拆除閘閥頂部或底部的連接以便于拆卸，或者如果可以完全拆除旋轉閘閥。清潔閘閥內部，清除所有商品和殘留物。插入一個符合電機轉子葉片尾端和閘閥驅動器邊緣板之間建議的最小間隙的千分尺。將儀表板向下拖動到電機轉子軸上，然后向上拖動到中心。如果儀表板捕捉到了所有內容，那么差距就太小了。如果有任何叮當聲或損壞可能會造成困難，請通過手動銼削或拋光突出的金屬材料進行修復。在閘閥的盲端重復整個過程。繼續操作后，對所有剩余的頂葉重復此過程。在電機轉子中心和底座軸承孔之間拖動塞尺，將其從一個現澆板滑動到另一個現澆筑板。隨后，在正常操作的所有方向上旋轉電機轉子，并檢查電機轉子葉片所有尖端的間隙。使用比建議的較大間隙大0.001的千分尺，并嘗試將其滑入所述的相同區域。如果氣壓表合適，您的旋轉供料器已剛開始損壞，將會沒法建立合理的密封性來控制粉末狀的流動性。

　　03 Check if the gap between the rotating feeder and the tender blade tip is inseparable, because the rotating feeder and gate valve must control the passage of very fine powder through the sometimes high pressure difference, so the gap between the tender blade tip must be very inseparable. Otherwise, the characteristics of your conveying system will face risks. To prevent potential problems caused by excessive steam leakage from the airlock, please tighten the gap as follows: Lock the switch power supply of the rotary feeder motor. If the connection at the top or bottom of the gate valve can be removed for ease of disassembly, or if the rotary gate valve can be completely removed. Clean the inside of the gate valve and remove all products and residues. Insert a micrometer that meets the recommended minimum gap between the motor rotor blade end and the gate valve driver edge plate. Drag the dashboard downwards onto the motor rotor shaft, and then upwards to the center. If the dashboard captures all the content, then the gap is too small. If there is any clanging or damage that may cause difficulties, please repair the protruding metal material by manually filing or polishing. Repeat the entire process at the blind end of the gate valve. After continuing the operation, repeat this process for all remaining top leaves. Drag a feeler gauge between the center of the motor rotor and the bearing hole of the base, and slide it from one cast-in-place plate to another. Subsequently, rotate the motor rotor in all directions of normal operation and check the clearances between all tips of the motor rotor blades. Use a micrometer with a gap 0.001 larger than the recommended one and try sliding it into the same area as described. If the pressure gauge is appropriate, your rotary feeder has just begun to be damaged and will not be able to establish a reasonable seal to control the flowability of the powder.

　　04為了防止旋轉給料機驅動系統的劣化，潤濕核心部件是很重要的。這包括減速器和變速器齒輪。應根據制造商的說明定期檢查和更換變速箱油位。傳動鏈和鏈輪（如有配備）應經常進行潤滑，尤其是當旋轉閥位于室外或清潔區時。如果您不確定閘閥的建議時間間隔，請參閱您的用戶手冊或聯系您的經銷商以獲取更多信息。

　　In order to prevent the deterioration of the drive system of the rotary feeder, it is important to wet the core components. This includes reducers and transmission gears. The transmission oil level should be checked and replaced regularly according to the manufacturer's instructions. The transmission chain and sprocket (if equipped) should be lubricated regularly, especially when the rotary valve is located outdoors or in a clean area. If you are unsure about the recommended time interval for gate valves, please refer to your user manual or contact your distributor for more information.

　　05當調整蹄襯和鏈輪以檢查旋轉給料機時，調整傳動齒輪和鏈輪，以確保鏈輪兩端對齊，并確保傳動鏈適當張緊。隨后，在進行維護之前，請確保防塵套襯里上的安全裝置已就位。

　　When adjusting the shoe lining and sprocket to check the rotary feeder, adjust the transmission gear and sprocket to ensure alignment at both ends of the sprocket and proper tension of the transmission chain. Subsequently, before carrying out maintenance, please ensure that the safety devices on the dust cover lining are in place.

　　06安裝觸摸檢測系統，以便在旋轉給料機容易損壞時發出警報。請安裝電機轉子觸摸檢測系統。該系統監測閘閥電機轉子與外殼的電氣隔離，當電機轉子接觸外殼時提供友好的提醒。該系統是保護您的產品免受金屬材料造成的環境污染的好方法，還可以避免對旋轉閥和供料器造成昂貴的損壞。

　　Install a touch detection system to issue an alarm when the rotating feeder is prone to damage. Please install a motor rotor touch detection system. The system monitors the electrical isolation between the gate valve motor rotor and the housing, providing friendly reminders when the motor rotor contacts the housing. This system is a great way to protect your products from environmental pollution caused by metal materials, and can also avoid expensive damage to rotary valves and feeders.

　　本文由 旋轉供料器  友情奉獻.更多有關的知識請點擊  http://www.sdyshjx.com/  真誠的態度.為您提供為全面的服務.更多有關的知識我們將會陸續向大家奉獻.敬請期待.

　　This article is a friendly contribution from the rotating feeder For more related knowledge, please click http://www.sdyshjx.com/ Sincere attitude To provide you with comprehensive services We will gradually contribute more relevant knowledge to everyone Coming soon.