三葉羅茨風機憑借其獨特性能，在污水處理、氣力輸送、真空包裝等諸多領域中得到廣泛應用，然而，在長期運行過程中，不可避免地會出現多種故障問題，以下將從主要故障類型、成因剖析以及對應的解決策略展開詳細闡述。

Three leaf Roots blowers have been widely used in various fields such as sewage treatment, pneumatic conveying, and vacuum packaging due to their unique performance. However, in long-term operation, various fault problems are inevitable. The following will elaborate on the main types of faults, causes, and corresponding solutions.

風量不足或壓力下降這一故障，成因較為復雜。進氣口堵塞是常見原因之一，濾網或消聲器積塵會阻礙進氣的順暢性；對于皮帶傳動型風機，皮帶打滑也是導致問題的因素，張緊力不足或皮帶磨損均會影響傳動效率；長期運行致使葉輪磨損，進而使得葉輪與殼體間隙增大，當間隙超出標準范圍（0.10 - 0.25mm）時，便會影響風機性能；此外，系統泄漏，包括管道、法蘭或密封部位的漏氣，同樣會造成風量與壓力的下降。針對這些問題，相應的解決方案為清潔或更換濾芯以保障進氣通暢；依據廠家要求調整皮帶張力或及時更換新皮帶，確保其具備合適的撓度；細致檢查葉輪間隙，若超標則需進行修復或更換葉輪處理；采用肥皂水檢測漏氣點，通過緊固螺栓或更換密封墊片的方式解決泄漏問題。

The cause of insufficient air volume or pressure drop is quite complex. Air intake blockage is one of the common reasons, as dust accumulation in filters or mufflers can hinder the smoothness of air intake; For belt driven fans, belt slippage is also a contributing factor, as insufficient tension or belt wear can affect transmission efficiency; Long term operation leads to impeller wear, which in turn increases the gap between the impeller and the housing. When the gap exceeds the standard range (0.10-0.25mm), it will affect the performance of the fan; In addition, system leaks, including leaks in pipelines, flanges, or sealing areas, can also cause a decrease in air volume and pressure. The corresponding solution to these problems is to clean or replace the filter element to ensure smooth air intake; Adjust the belt tension according to the manufacturer's requirements or replace the belt with a new one in a timely manner to ensure that it has appropriate deflection; Carefully inspect the clearance between the impellers. If it exceeds the standard, repair or replace the impellers; Use soapy water to detect leakage points, and solve the leakage problem by tightening bolts or replacing sealing gaskets.

風機出現過熱（軸承 / 殼體溫度高）的情況，存在多種潛在原因。潤滑油不足或變質，即齒輪箱缺油或者油品發生劣化，會致使?jié)櫥Ч患?；冷卻不良也是重要因素，風冷型風機散熱片積灰會影響散熱，水冷型風機冷卻水流量不足則無法有效帶走熱量；過載運行，當系統阻力過大或排氣壓力超過額定值時，會使風機負荷加重從而產生過多熱量；軸承損壞，因潤滑不良或疲勞磨損導致軸承卡死，也會引發過熱現象。解決該問題需要檢查油位，及時補充或更換推薦的 ISO VG 220 齒輪油；清理散熱片或全面檢查冷卻水系統，確保水冷型風機的冷卻水流量達到或超過 2m3/h；合理調整工況，通過加裝安全閥或采用變頻調速的方式避免超壓運行；更換耐高溫軸承，如選用 SKF/C&U 等品牌的優質軸承。

There are multiple potential reasons for the overheating of the fan (high bearing/housing temperature). Insufficient or deteriorated lubricating oil, i.e. gearbox oil shortage or oil degradation, can lead to poor lubrication effect; Poor cooling is also an important factor. Dust accumulation on the cooling fins of air-cooled fans can affect heat dissipation, while insufficient cooling water flow in water-cooled fans cannot effectively remove heat; Overload operation, when the system resistance is too high or the exhaust pressure exceeds the rated value, will increase the load on the fan and generate excessive heat; Bearing damage, caused by poor lubrication or fatigue wear leading to bearing jamming, can also cause overheating. To solve this problem, it is necessary to check the oil level and promptly replenish or replace the recommended ISO VG 220 gear oil; Clean the heat sink or conduct a comprehensive inspection of the cooling water system to ensure that the cooling water flow rate of the water-cooled fan reaches or exceeds 2m 3/h; Reasonably adjust the working conditions and avoid overpressure operation by installing safety valves or using variable frequency speed regulation; Replace high-temperature resistant bearings, such as using high-quality bearings from SKF/C&U brands.

異常振動或噪音大的故障，其根源主要涉及多個方面。葉輪動平衡失效，葉輪粘附雜質或發生腐蝕會破壞其平衡狀態；聯軸器 / 皮帶輪不對中，安裝偏差若超過 0.05mm/m，會在運行中產生振動與噪音；地腳螺栓松動，長期振動容易導致固定螺栓松脫，影響風機的穩定性；齒輪磨損，同步齒輪嚙合不良會產生沖擊噪聲。解決此類問題需要清潔葉輪或重新進行動平衡處理，將不平衡量控制在≤1g 的范圍內；使用激光對中儀校正聯軸器同心度，使其偏差調整至 ±0.02mm；緊固地腳螺栓，并加裝防松墊片以增強固定效果；檢查齒輪磨損情況，若磨損嚴重則需及時更換齒輪組。

The root cause of abnormal vibration or loud noise faults mainly involves multiple aspects. Failure of impeller dynamic balance, adhesion of impurities or corrosion to the impeller can disrupt its balance state; If the coupling/pulley is misaligned and the installation deviation exceeds 0.05mm/m, vibration and noise will be generated during operation; Loose anchor bolts and long-term vibration can easily cause the fixing bolts to loosen, affecting the stability of the fan; Gear wear and poor meshing of synchronous gears can generate impact noise. To solve such problems, it is necessary to clean the impeller or perform dynamic balancing again to control the unbalance within the range of ≤ 1g; Use a laser alignment instrument to calibrate the concentricity of the coupling and adjust its deviation to ± 0.02mm; Tighten the anchor bolts and install anti loosening washers to enhance the fixing effect; Check the wear of the gears, and if the wear is severe, replace the gear set in a timely manner.

漏油（齒輪箱或軸封處）故障主要由以下原因引發。油封老化是常見因素，長期高溫運行會使橡膠密封硬化開裂，從而失去密封作用；油位過高會導致齒輪箱內油壓過大，油液便會從呼吸閥滲出；軸磨損，軸封部位因長期摩擦產生溝槽，也會造成漏油。解決漏油問題需要更換性能優良的油封，推薦采用氟橡膠或聚四氟乙烯材質的油封；調整油位至油標中線位置，且需在運行狀態下進行檢查確認；對磨損的軸套進行修復或更換處理，可通過鍍鉻的方式修復磨損部位。

Oil leakage (at gearbox or shaft seal) faults are mainly caused by the following reasons. Oil seal aging is a common factor, and long-term high-temperature operation can cause rubber seals to harden and crack, thereby losing their sealing function; Excessive oil level can cause excessive oil pressure in the gearbox, leading to oil leakage from the breather valve; Shaft wear and groove formation in the shaft seal area due to long-term friction can also cause oil leakage. To solve the oil leakage problem, it is necessary to replace the high-performance oil seal. It is recommended to use oil seals made of fluororubber or polytetrafluoroethylene material; Adjust the oil level to the center line of the oil gauge and check and confirm it while in operation; The worn shaft sleeve can be repaired or replaced by chrome plating.

電機過載跳閘同樣存在多種可能原因。電壓不穩定，當電網電壓波動超過 ±10% 時，會影響電機的正常運行；進口阻力大，濾網堵塞或閥門未全開，會增加風機的運行負荷；風機內部卡滯，異物進入或軸承損壞等情況會阻礙風機的正常運轉。針對這些問題，有效的解決方案包括加裝穩壓器或仔細檢查供電線路，以確保電壓穩定；清理進口管道，保證閥門處于全開狀態，減少進氣阻力；手動盤車檢查風機，及時排除卡死故障，保障風機的順暢運行 。

There are also multiple possible reasons for motor overload tripping. Voltage instability, when the voltage fluctuation of the power grid exceeds ± 10%, will affect the normal operation of the motor; High import resistance, clogged filter screens or valves not fully open can increase the operating load of the fan; Internal jamming, foreign objects entering, or damaged bearings can hinder the normal operation of the fan. Effective solutions to these issues include installing voltage regulators or carefully inspecting power supply lines to ensure voltage stability; Clean the inlet pipeline to ensure that the valve is fully open and reduce intake resistance; Manually rotate and inspect the fan, promptly eliminate any stuck faults, and ensure the smooth operation of the fan.

本文由三葉羅茨風機友情奉獻.更多有關的知識請點擊:http://m.kingwanlan.com我們將會對您提出的疑問進行詳細的解答，歡迎您登錄網站留言.

This article is a friendly contribution from Roots blower For more information, please click: http://m.kingwanlan.com We will provide detailed answers to your questions. You are welcome to log in to our website and leave a message